Affordable Bathroom Remodeling Walkertown

Looking for the Best Residential and Commercial Roofing Company in Walkertown

 

We believe that a roof is the most integral part of a home. It’s what holds your walls together and keeps your house, your possessions, and your family safe and secure.

Kitchen Remodeling Quotes

Roofing - A Guide To Installing Corrugated Iron Roofing

Corrugated Iron Roofing is durable, lightweight and easy to install. If a few extra precautions are taken with handling and fixing, the finished product will greatly be improved.

White Rust
Over half of the mistakes made while constructing a corrugated iron roof can be traced back to incorrect storage or handling. The iron has to be handled and stored correctly because the surface is very easily damaged.

Leave the metal roofing at the manufacturers until you are ready to start installing it. Aim for delivery the day before roofing starts. If the roofing iron arrives before you are able to fix it, you must ensure it is kept bone dry. It is a common mistake to assume that because they are roofing sheets, they can withstand moisture. If the roofing sheets are stacked together and they get wet, they will stain. White rust forms on the coating and it is very difficult to remove. If your roof sheets do get wet, separate each individual sheet. Use bearers to allow airflow around the metal. This will prevent the corrosion.

Gently does it
As for handling, care needs to be taken in order not to damage the paintwork. Sliding sheets across one another will damage them. When separating the roofing sheets, you should lift them cleanly upwards without scratching the one underneath.

Spend more money
Installing a roof can be time consuming and costly. The last thing you need is to have to keep spending money on maintenance. If you scrimp on the cost of fasteners you will forever be replacing loose nails and fixing leaks. Choose good quality roofing screws. These will provide a more secure fixing and last as long as the roofing iron. It's important not to over tighten the screws. Just tight enough to lightly compress the neoprene washer is sufficient.

Drilling
If you pre-drill the holes for your roofing screws on the ground, it will be safer and give the roofing a neater appearance. This is only possible if the purlins run parallel to the eaves and the roof is reasonably square.

Using a quality drill bit makes the job easier. The drill bit should be slightly larger than the diameter of the roofing screws. This will prevent stress fractures as the sheets expand and contract.

Take accurate measurements of the purlin centres from the eaves and mark the roofing sheets ready for drilling the screw holes. Don't forget to add the drop into the gutter to your measurements, usually about 50mm. It's better to use chalk for marking corrugated roofing iron because pencil may damage the surface.

Cut to the quick
Cutting corrugated iron roofing sheets with a disc cutter makes the job easier and faster. Unfortunately, it also damages the roofing iron beyond repair. Hot particles of steel imbed themselves into the surrounding metal allowing it to corrode. Nibblers will do the job adequately as long as you are careful with the swarf. It's preferable to cut the sheet with hand shears or best of all power shears. A better finish can be achieved if you make two cuts. The first cut 50mm away from your finished edge allowing you to neatly trim to the line with your second cut.

Scratches
If you find scratches on your roofing during installation resist the urge to paint it. The paint may well look like a good match from the tin, but after a couple of seasons weathering the patched paintwork will stick out like a sore thumb. Contact the manufacturer and ask for advice on making repairs to their product.

Laying the roofing
Before you start laying the roofing sheets check that the roof is square. If the roof is not square you can still achieve a good finish if you even out the difference, between the two barges. The difference will then be less noticeable as it will be covered by the barge flashing. Run a string line along the eaves, 50mm into the gutter and it will provide you with a straight edge for the roofing sheets.

Clean up
On completion it's important to clear the roof of any loose swarf. Tiny particles of iron left on the roof will rust and ruin the surface. A soft brush will do the job or ideally a leaf blower can be used.

A well installed corrugated iron roof will give years of maintenance free service. If you take a little extra care with the preparation and fixing, you will achieve a superior finish.

Affordable Bathroom Remodeling

Emergency Exterior Remodeling

Is Colorbond Roofing Better Than Concrete Tiles? It Depends On Taste, Lifestyle and Budget

Roof valleys are a frequent source of leaks in older houses. Installation procedures differ depending on the roof type and materials used. We will look here at the basic installation of an open lead lined roof valley.

A roof valley is basically a gutter set between two meeting pitched roofs. Depending on the roof area it serves, the valley is the exit point for a large volume of water so extreme care should be taken with installation. If the roof has been leaking for a while or if there are any signs of rot, you will need to start by replacing the valley boards. Lead sheet is not self supporting and should be placed on treated roofing boards of sufficient strength to hold a large person. (Most roofing contractors are big guys!) Fit boards of sufficient width to accommodate the lead plus 100mm either side. This will give you something to nail the roofing batons to.

The top of the valley boards should be at the same level as the top of the roof rafters. If you lay the boards directly on top of the rafters it may cause the roofing tiles to kick up and restrict water run off. You will need to cut the valley boards to fit in between the rafters. Support the valley boards with studs or noggins. The valley should finish on an even plane at the eaves. It should not kick up higher than the bottom rafters. If it does, you will need to cut the fascia board or adjust the gutter to suit. It is a good idea to fit a tilting fillet each side of the valley. This angled strip of wood runs along the valley length and should be a minimum of 150mm from the centre of the valley. It should sit no higher than the roofing batons with the thinnest end closest to the centre of the valley.

It is common practice to fit a single sheet of roofing underlay the entire length of the valley. The adjacent roofing underlay will rest on top of this sheet. I recommend you use one of the new advanced synthetic underlay materials. The older bitumen based felts are fine for normal roofing situations but are not suitable for valleys. Over time the bitumen will bond the lead to the boards and restrict thermal movement. You should ensure you buy lead of a sufficient grade/code for valley applications. This should be between 1.80mm and 2.24mm thickness. If you are unsure ask your roofing merchant of the correct grade. The lead should be cut into sections no larger than 1.5 meters in length to allow sufficient thermal movement. Bend a welt into the lead 25mm each side. This acts as a last line of defence for water penetration. It also has the added benefit of stiffening the lead, which makes carrying it up the roof a lot easier.

Starting at the bottom of the valley, dress the lead neatly onto the valley boards and over the tilting fillets. The bottom of the lead should allow correct drainage into the gutter. Fix two rows of nails at the very top of the flashing. Use copper or stainless steel nails. Never use galvanised or aluminum nails which will just react with the lead and corrode. I recommend you use the minimum amount of fixing possible to hold the lead in place. If you over fix lead sheeting it will eventually split due to thermal movement. So don't nail the sides. When you have successfully dressed the first sheet you can move up the roof laying subsequent sheets. Overlap each sheet a minimum of 150mm. On lower pitched roof valleys you will need to increase the lap. Where the valley ends at the ridge, you will need to dress the lead so it can sit neatly under the ridge tiles. You are now ready to start fixing the batons and laying the roofing tiles. The key points to remember are to keep the sheet lengths down to 1.5 meters and don't over fix. If you follow the procedure outlined and take care with the dressing you will produce a durable maintenance free valley.

Kitchen Remodeling Cost

Roofing is one of the most important investments you can make. Improper, aged or substandard roofing can lead to a host of other more expensive problems. If you are selling your property, a well-chosen roof can yield a solid return on your investment. Whatever your budget or design desires, whether you want architectural shingles, tile roof installation or something in between, a Roof Master consultant will work with you to make it a reality.

 

Ruine Process Roofing prides itself in providing Residential and Commercial Roofing services in Walkertown . We support local businesses and hope you do too!

Ruine remodeling specializes in all major types of roofing services, whether you need a new roof/roof replacementplanned roof maintenance, or emergency roof repair. 
 
Need a free estimate? Call us today or send us a message here.

Bathroom Remodeling Quotes North Carolina

Affordable Bathroom Remodeling Walkertown

Affordable Bathroom Remodeling Walkertown